Check Engine Light Service Jeep Wrangler

What do you do when you’re driving along in your Jeep Wrangler and suddenly, a yellow light illuminates on your dash and says "Check Engine". If you’re like most Jeep owners, your heart sinks a little because you have little idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep breath and realize the light coming on doesn’t mean you have to pull the car over to the side of the road and call a tow truck, but it is recommended that you get your Jeep Wrangler checked as soon as possible. Ignoring that warning could end up causing major damage to expensive engine components.

When your Jeep Wrangler's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t correct, a computer turns on your check engine light. This amber or yellow light is typically labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that identifies as the issue, whether it's a sensor or a failing engine part. This code is read with an electronic scan tool that is used by our Jeep auto repair mechanics at Mike Shaw Chrysler Dodge Jeep Ram. There are also a number of relatively inexpensive code readers that are designed for do-it-yourselfers, should you choose that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an experienced professional to determine the issue and repair it.

What could cause the check engine light to come on in a Jeep Wrangler?

When your check engine light comes on, this could be as simple as tightening or replacing your gas cap. Likewise, the check engine light could also be a warning of a serious problem that could cause serious damage to your engine and come with a hefty repair bill. Depending on your make and model, the check engine light will illuminate or blink. A steady glow typically means something less serious but a flashing check engine light indicates that your vehicle’s engine is in serious trouble and service is needed immediately. If your check engine light is flashing in your Jeep Wrangler, we highly recommend not to drive the vehicle and schedule Jeep service today. Below is a list of the most common reasons your check engine light can come on:

• New Spark Plugs or Plug Wires are decisive for your Jeep Wrangler. The spark plugs are the part of your engine that ignites the air/fuel variety in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If you're spark plugs or spark plug wires are bad or popular, you will experience low performance and reduced power. In some extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, best to more expensive repairs.
• Issues with any aftermarket items. An aftermarket alarm, exhaust or other item can wreak havoc on your Jeep Wrangler if it’s not installed properly. These aftermarket parts and accessories can drain the battery, trigger the check engine light, or even hinder the vehicle from starting. If these issues sound popular, deliver your Wrangler to Jeep and have our team of certified mechanics ensure that your aftermarket items were installed perfectly and aren't causing any issue. Getting accessories, excessively aftermarket parts and accessories, or using OEM parts first place might cost a little bit more but could save you money from having to get low work and damage caused by low installation work corrected.
• Your Jeep Wrangler has a vacuum leak. Every Jeep Wrangler has a vacuum system that performs a wide variety of functions. The vacuum system also helps reduce harmful emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dry out and crack, excessively if they’re exposed to imposing heat or extreme bleak.
• One of the most common and several cause is that your Jeep Wrangler gas cap is loose, damaged or missing. The gas cap for your Jeep Wrangler serves multiple purposes. It prevents gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a bad fuel cap? If your gas cap is popular or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump. Luckily, to replace a gas cap isn't expensive. If your check engine light turns on suddenly after you put gas in your Jeep Wrangler, first thing you should check is to make courageous the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.
• The battery is low or dead. The battery in your Jeep Wrangler is every tall. Without a car battery, your car won’t start, light up the road ahead, play the radio or charge your phone. Today’s car batteries last much longer than they did a few decades ago, and they don't really require maintenance. The price of a new one depends on the type of Jeep you commute, but check our ongoing service coupons and specials.
So what happens if I don’t replace your O2 sensor? A faulty sensor can not only affect your miles per gallon, but it can cause damage to your catalytic converter and your Jeep Wrangler's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to represent the polite variety of air and fuel that enters the cylinders in your engine. A bad O2 sensor can also cause a car to fail an emissions test.
• Your catalytic converter is bad or going bad. The catalytic converter is a part of your Jeep Wrangler’s exhaust system. The catalytic converter's work is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is frequently caused by neglected maintenance, which is why Mike Shaw Chrysler Dodge Jeep Ram offers a complimentary multi-point inspection with every Jeep service. If you have an issue with your catalytic converter and don't get it repaired, your Jeep Wrangler will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your car may run at a higher temperature, too, which can cause other problems from overheating.
• Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, known as the O2 sensor, measures the amount of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns faster and your vehicle will be less convenient when it comes to fuel economy.
• Your mass airflow sensor (known as MAF) needs to be replaced. The mass airflow sensor in your Jeep Wrangler is what determines how much fuel is decisive to run your engine efficiently by measuring the amount of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to aware changes, like altitude. If your Jeep Wrangler is having trouble starting, idling rough or has a sudden change in the position of the throttle pedal, this could be a sign of a bad mass airflow sensor.

Will the check engine light reset itself?

The check engine light on your Jeep Wrangler will usually shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will turn itself off. Likewise, if your catalytic converter is going functional, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your Jeep Wrangler light will go off after about 20-40 miles. If you drive over that amount and the light is still on, you will need to bring it in to Mike Shaw Chrysler Dodge Jeep Ram so the light and code can be double-checked and reset.

Jeep Wrangler Check Engine Light Codes

The check engine light turning on can be quite intimidating to see that little light on your vehicle’s dashboard suddenly illuminates, but in reality, it is not something that should cause you to shut down in fear right away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, also known as the OBD (on-board computer diagnostic system) in your Wrangler. There are hundreds of different codes that your check engine light can represent. While that sounds daunting, with a little patience, tackling basic diagnostics will give you useful knowledge about your vehicle and will also allow that Check Engine Light to do what it is really supposed to do: be your guide. Unfortunately, obvious and helpful vehicle symptoms do not always accompany an illuminated Check Engine Light. Since there are hundreds of possible OBD codes, there are also hundreds of possible reasons for the light, including:

• Loose Gas Cap or Missing Gas Cap
• Fuel and air metering systems problems
• Transmission issues
• Bad Spark Plugs
• Computer output circuit issues
• Emissions controls issues
• Ignition system faults
• Old Battery
• O2 Sensor

This is why it is important for someone who does not have a lot of automotive knowledge to not assume what a code means. If the engine light comes on due to a adequate concern, you risk damaging your car additional by not repairing the issue prudent away. Call Mike Shaw Chrysler Dodge Jeep Ram at 9702364701 straightaway or schedule your check engine light service online today! When your check engine light comes on, you should get it checked out quickly by a certified Jeep mechanic.

Jeep Wrangler Check Engine Light Flashing

Although there are countless potential causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are several common causes including something as simple as a loose gas cap. Other common reasons for a Check Engine Light are faulty head gasket, a malfunction with the fuel injection system, dirty mass airflow sensor, faulty emissions control part, damaged oxygen sensor, or defective spark plugs to name a few. No matter what is the root cause of the Check Engine Light, we have the Jeep Certified Technicians and the certified service protocol to isolate the root problem and repair it as needed to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Jeep issue was fixed.

Every Jeep Wrangler was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the vehicle on its crucial systems. The sensors are continually detecting conditions while sending data to the electronic control unit. If the electronic control unit detects that the data is out of factory specifications, the Check Engine Light illuminates telling you that there is a problem. However, that is the limitation of the Check Engine Light – it won’t tell you what exactly is wrong nor what to do about it. That’s where we come in; Mike Shaw Chrysler Dodge Jeep Ram provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Highly Qualified Service professional.

What Does the Check Engine Light Mean?

One of the most commonly misunderstood lights or indicators in your Jeep Wrangler is the check engine light. The check engine light is part of the onboard diagnostics system, and displays in a few different ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your vehicle. Onboard computers increasingly have controlled and monitored vehicle performance since the 80s and do a variety of things for your Jeep Wrangler. Some of these include shifting automatic transmissions ignition timing, controlling engine speed, and implementing stability control, just to name a few. With that being said, the check engine light can mean a variety of different things. It can be as simple as your gas cap being loose or as serious as engine knocking. If your check engine light is on in your Jeep Wrangler, contact Mike Shaw Chrysler Dodge Jeep Ram. Our Jeep service department can assist you find out what code is turning your check engine light on or diagnose why your check engine light is flashing. Contact Mike Shaw Chrysler Dodge Jeep Ram today!

Is it safe to drive your Jeep Wrangler with the check engine light on?

If the check engine light is flashing, this means that there is a genuine issue and it is recommended to service your Jeep Wrangler immediately. This question is not exceedingly uncomplicated because it each depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be protected to drive. This is frequently indicated by a practical glow of the check engine light. If you notice a range in the performance of the automobile, it could be an indication of a more genuine problem. Call the experts at Mike Shaw Chrysler Dodge Jeep Ram by dialing 9702364701 so you can describe the issues. Or reduce your speed and bring your Jeep to our certified mechanics as soon as experienced.

Jeep Wrangler Check Engine Light

A flashing light indicates that the problem is critical and if not taken care of hastily may result in divergent damage to the vehicle. If the check engine light in your Jeep Wrangler starts flashing, that means that the problem needs immediate attention and your Jeep should be brought in hastily. This blinking light usually indicates a severe engine misfire allowing unburned fuel to be dumped into the exhaust system. There it can quickly raise the temperature of the catalytic converter to a point where damage is likely, requiring an expensive repair. Some owners ask if spark plugs cause the check engine light to flash? This can absolutely be the cause. A bad, old or dirty spark plug can cause the engine to misfire. If your check engine light is flashing, please contact our unit of automotive experts at Mike Shaw Chrysler Dodge Jeep Ram shortly by calling 9702364701. If the problem is ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a very expensive repair.

How many miles can you drive with the check engine light?

The safest bet is to decipher the code and then plan your strategy accordingly. It could be anything from a bad sensor to plug wires needing to be replaced. Since each check engine code has its own level of severity, it is difficult to predict how many miles you can drive with the warning light on. If you check engine light is flashing, we advocate that you pull over and contact Mike Shaw Chrysler Dodge Jeep Ram to aid determine if your vehicle is safe to drive in or if we advocate a tow truck.

How much does it cost to get the engine light checked?

The check engine light warns of issues ranging from a gas cap that's not well tightened to a more adequate failure like a bad catalytic converter or a problem with one of the car's oxygen sensors, so it positive to get the usable code reading and diagnosis. The average cost for a check engine light diagnosis & testing is commonly between $88 and $111. The positive news, Mike Shaw Chrysler Dodge Jeep Ram offers complimentary multi-point inspections and free diagnostics, in most cases, to assist pick the cause of your check engine light.