Please wait while the page loads...

2013 Ram 2500 Check Engine Light Codes

The check engine light turning on can be quite intimidating to see that little light on your vehicle’s dashboard suddenly illuminates, but in reality, it is not something that should cause you to shut down in fear right away. If you hear the term, diagnostic trouble codes (DTC), these are just another name for check engine light codes. These are automotive computer codes stored by the ECM, also known as the OBD (on-board computer diagnostic system) in your 2500. There are hundreds of different codes that your check engine light can represent. While that sounds daunting, with a little patience, tackling basic diagnostics will give you useful knowledge about your vehicle and will also allow that Check Engine Light to do what it is really supposed to do: be your guide. Unfortunately, obvious and helpful vehicle symptoms do not always accompany an illuminated Check Engine Light. Since there are hundreds of possible OBD codes, there are also hundreds of possible reasons for the light, including:

  • Emissions controls issues
  • Bad Spark Plugs
  • Computer output circuit issues
  • O2 Sensor
  • Ignition system faults
  • Transmission issues
  • Old Battery
  • Fuel and air metering systems problems
  • Loose Gas Cap or Missing Gas Cap
This is why it is important for someone who does not have a lot of automotive knowledge to not assume what a code means. Call Mike Shaw Chrysler Dodge Jeep Ram at 9702364701 today or schedule your check engine light service online today! When your check engine light comes on, you should get it checked out quickly by a certified Ram mechanic. If the engine light comes on due to a risky concern, you risk damaging your car further by not repairing the issue reasonable away.

2013 Ram 2500 Check Engine Light Flashing

Although there are countless potential causes of an illuminated Check Engine Light, we know from years of providing Check Engine Light Diagnosis Service that there are several common causes including something as simple as a loose gas cap. Other common reasons for a Check Engine Light are a malfunction with the fuel injection system, damaged oxygen sensor, faulty head gasket, dirty mass airflow sensor, faulty emissions control part, or defective spark plugs to name a few. No matter what is the root cause of the Check Engine Light, we have the Ram Certified Technicians and the certified service protocol to isolate the root problem and repair it as needed to restore factory specifications. When this happens, the Check Engine Light turns off, and you can leave the service center knowing that your Ram issue was fixed.

Every 2013 Ram 2500 was designed with a high-technology performance monitoring system with a computer, and a series of sensors positioned strategically throughout the vehicle on its crucial systems. The sensors are continually detecting conditions while sending data to the electronic control unit. If the electronic control unit detects that the data is out of factory specifications, the Check Engine Light illuminates telling you that there is a problem. However, that is the limitation of the Check Engine Light – it won’t tell you what exactly is wrong nor what to do about it. That’s where we come in; Mike Shaw Chrysler Dodge Jeep Ram provides a Check Engine Light Diagnosis Service that isolates the core problem and gives you a recommendation on what to do next from a Highly Qualified Service professional.

Will the check engine light reset itself?

The check engine light on your 2013 Ram 2500 will usually shut itself off if the issue or code that caused it to turn on is fixed. For example, if the cause of your check engine light coming on was a loose gas cap, if it's tightened, the light will turn itself off. Likewise, if your catalytic converter is going functional, and you did a lot of stop-and-go driving, that may have turned on the check engine light due to the high usage of the converter. In most cases, your 2013 Ram 2500 light will go off after about 20-40 miles. If you drive over that amount and the light is still on, you will need to bring it in to Mike Shaw Chrysler Dodge Jeep Ram so the light and code can be double-checked and reset.

Is it safe to drive your 2013 Ram 2500 with the check engine light on?

If the check engine light is blinking, this means that there is a genuine issue and it is recommended to service your Ram 2500 instantly. This question is not very uncomplicated because it all depends on the severity of the issue. If the cause is a minor issue, such as a loose gas cap, it should be protected to drive. This is usually indicated by a steady glow of the check engine light. If you notice a array in the performance of the vehicle, it could be an indication of a more substantial problem. Call the advisors at Mike Shaw Chrysler Dodge Jeep Ram by dialing 9702364701 so you can describe the issues. Or cut down your speed and bring your 2013 Ram to our certified mechanics as soon as potential.

What Does the Check Engine Light Mean?

One of the most commonly misunderstood lights or indicators in your 2013 Ram 2500 is the check engine light. The check engine light is part of the onboard diagnostics system, and displays in a few different ways. It can say "Check Engine", it can be a symbol of an engine, it can even be a combination of both. This light illuminates in either an amber or red color and is part of the diagnostics system found on your vehicle. Onboard computers increasingly have controlled and monitored vehicle performance since the 80s and do a variety of things for your 2013 Ram 2500. Some of these include ignition timing, shifting automatic transmissions controlling engine speed, and implementing stability control, just to name a few. With that being said, the check engine light can mean a variety of different things. It can be as simple as your gas cap being loose or as serious as engine knocking. If your check engine light is on in your 2013 Ram 2500, contact Mike Shaw Chrysler Dodge Jeep Ram. Contact Mike Shaw Chrysler Dodge Jeep Ram today! Our Ram service department can help you find out what code is turning your check engine light on or diagnose why your check engine light is flashing.

How many miles can you drive with the check engine light?

The safest bet is to decipher the code and then plan your strategy accordingly. Since each check engine code has its own level of severity, it is not nice to predict how many miles you can drive with the warning light on. It could be anything from a bad sensor to plug wires needing to be replaced. If you check engine light is flashing, we recommend that you pull over and contact Mike Shaw Chrysler Dodge Jeep Ram to assist determine if your vehicle is safe to drive in or if we recommend a tow truck.

2013 Ram 2500 Check Engine Light

A flashing light indicates that the problem is compatible and if not taken care of abruptly may result in leading damage to the vehicle. If the check engine light in your 2013 Ram 2500 starts flashing, that means that the problem needs sudden attention and your Ram should be brought in abruptly. This blinking light usually indicates a severe engine misfire allowing unburned fuel to be dumped into the exhaust system. There it can quickly raise the temperature of the catalytic converter to a point where damage is likely, requiring an expensive repair. Some owners ask if spark plugs cause the check engine light to flash? This can absolutely be the cause. A bad, old or dirty spark plug can cause the engine to misfire. If your check engine light is blinking, please contact our team of automotive experts at Mike Shaw Chrysler Dodge Jeep Ram suddenly by calling 9702364701. If the problem is ignored or you continue to drive, this can spread to the spark plug wires, catalytic converter, or ignition coils which can lead to a very expensive repair.

How much does it cost to get the engine light checked?

The average cost for a check engine light diagnosis & testing is customarily between $88 and $111. The cooperative news, Mike Shaw Chrysler Dodge Jeep Ram offers complimentary multi-point inspections and free diagnostics, in most cases, to aid imply the cause of your check engine light. The check engine light warns of issues ranging from a gas cap that's not properly tightened to a more forceful failure like a bad catalytic converter or a problem with one of the car's oxygen sensors, so it cooperative to get the apt code reading and diagnosis.

Check Engine Light Service 2013 Ram 2500

What do you do when you’re driving along in your Ram 2500 and suddenly, a yellow light illuminates on your dash and says "Check Engine". If you’re like most Ram owners, your heart sinks a little because you have little idea about what that light is trying to tell you or how you should react. The fear of the unknown (or the cost of the unknown) can be just as stressful. But take a deep breath and realize the light coming on doesn’t mean you have to pull the car over to the side of the road and call a tow truck, but it is recommended that you get your 2013 Ram 2500 checked as soon as possible. Ignoring that warning could end up causing major damage to expensive engine components.

When your 2013 Ram 2500's ECM (electronic control module), which is the vehicle's onboard computer, finds a problem in the electronic control system that it can’t correct, a computer turns on your check engine light. This amber or yellow light is typically labeled “check engine” or “service engine soon”, or the light may be nothing more than a picture of an engine, or a picture of the engine with the word “check.”

When the light turns on, the ECM stores an engine code or “trouble code” in its memory that identifies as the issue, whether it's a sensor or a failing engine part. This code is read with an electronic scan tool that is used by our Ram auto repair mechanics at Mike Shaw Chrysler Dodge Jeep Ram. There are also a number of relatively inexpensive code readers that are designed for do-it-yourselfers, should you choose that route too. While this code will tell you the issue that is detected, a true diagnosis still requires an experienced professional to determine the issue and repair it.

What could cause the check engine light to come on in a 2013 Ram 2500?

When your check engine light comes on, this could be as simple as tightening or replacing your gas cap. Likewise, the check engine light could also be a warning of a serious problem that could cause serious damage to your engine and come with a hefty repair bill. Depending on your make and model, the check engine light will illuminate or blink. A steady glow typically means something less serious but a flashing check engine light indicates that your vehicle’s engine is in serious trouble and service is needed immediately. If your check engine light is flashing in your 2013 Ram 2500, we highly recommend not to drive the vehicle and schedule Ram service today. Below is a list of the most common reasons your check engine light can come on:

  • Your catalytic converter is bad or going bad. The catalytic converter is a part of your 2013 Ram 2500’s exhaust system. The catalytic converter's function is to turn the carbon monoxide created by the combustion process into carbon dioxide. A damaged catalytic converter is usually caused by neglected maintenance, which is why Mike Shaw Chrysler Dodge Jeep Ram offers a complimentary multi-point inspection with every Ram service. If you have an issue with your catalytic converter and don't get it repaired, your 2013 Ram 2500 will not pass an emissions test, show a lack of engine performance and will negatively affect your fuel economy. Your car may run at a higher temperature, too, which can cause alternative problems from overheating.
  • Your O2 Sensor (Oxygen Sensor) needs to be replaced. The Oxygen sensor, known as the O2 sensor, measures the fee of oxygen in your exhaust system. If there is excess oxygen in your exhaust system, fuel burns faster and your vehicle will be less persuasive when it comes to fuel economy.
  • Your mass airflow sensor (known as MAF) needs to be replaced. The mass airflow sensor in your Ram 2500 is what determines how much fuel is mandatory to run your engine efficiently by measuring the fee of air entering the engine. As a part of the engine management system, the mass airflow sensor helps adjust to genuine changes, same altitude. If your Ram 2500 is having trouble starting, idling rough or has a sudden change in the position of the throttle pedal, this could be a sign of a bad mass airflow sensor.
  • One of the most natural and frequent cause is that your 2013 Ram 2500 gas cap is loose, damaged or missing. The gas cap for your 2013 Ram 2500 serves multiple purposes. It prevents gas fumes from being released when you aren't driving, it seals the fuel system and helps maintain pressure within the fuel tank. What happens if you have a bad fuel cap? If your gas cap is classical or has a ruptured seal, you can lose fuel through evaporation which will result in more trips to the pump. Luckily, to replace a gas cap isn't expensive. If your check engine light turns on quickly after you put gas in your 2013 Ram 2500, earliest thing you should check is to make bold the cap isn’t loose — or that it's still on your car’s roof or at the fuel pump.
  • So what happens if I don’t replace your O2 sensor? A faulty sensor can not only affect your miles per gallon, but it can cause damage to your catalytic converter and your 2013 Ram 2500's spark plugs. The O2 sensor sends data to the vehicle’s onboard computer to represent the honest variation of air and fuel that enters the cylinders in your engine. A bad O2 sensor can also cause a car to fail an emissions test.
  • The battery is low or dead. The battery in your 2013 Ram 2500 is every memorable. Without a car battery, your car won’t start, light up the road ahead, play the radio or charge your phone. Today’s car batteries last much longer than they did a few decades ago, and they don't really require maintenance. The price of a new one depends on the type of Ram you drive, but check our extant service coupons and specials.
  • Your 2013 Ram 2500 has a vacuum leak. Every Ram 2500 has a vacuum system that performs a wide collection of functions. The vacuum system also helps lower harmful emissions by routing the fumes as gasoline evaporates through the engine. If you notice that your RPM is high in idle or randomly surges, a vacuum leak could be the cause. Over time, vacuum hoses can dry out and crack, especially if they’re exposed to astonishing heat or extreme charming.
  • Issues with any aftermarket items. An aftermarket alarm, exhaust or alternative item can wreak havoc on your 2013 Ram 2500 if it’s not installed perfectly. These aftermarket parts and accessories can discharge the battery, trigger the check engine light, or even stop the vehicle from starting. If these issues sound favored, bring your 2500 to Ram and have our team of certified mechanics ensure that your aftermarket items were installed appropriately and aren't causing any issue. Getting accessories, especially aftermarket parts and accessories, or using OEM parts earliest place might rate a little bit more but could save you money from having to get poor work and damage caused by poor installation work corrected.
  • New Spark Plugs or Plug Wires are mandatory for your 2013 Ram 2500. The spark plugs are the part of your engine that ignites the air/fuel variation in the combustion chamber of your vehicle. This explosion is what moves the pistons and makes the engine run. The spark plug wires deliver the spark from the ignition coil to the spark plugs. If your spark plugs or spark plug wires are bad or classical, you will experience poor performance and reduced power. In a little extreme cases, your engine will have trouble starting or continuing to run. Worn spark plugs and plug wires can cause clogged catalytic converter or damage to ignition coils and O2 sensors, best to more expensive repairs.